Page 1 of 2 12 LastLast
Results 1 to 6 of 7

Thread: Riser - paint chipped and peeling in limb pockets. Repair suggestions?

  1. #1
    In the Blue jonUK76's Avatar
    Join Date
    Sep 2016
    Location
    South Wales
    Posts
    111
    Thanks
    28
    Thanked 28 Times in 21 Posts

    Riser - paint chipped and peeling in limb pockets. Repair suggestions?

    I recently got a used blue W&W Winex riser which is a painted, as opposed to anodised riser. It looks very good externally but in the limb pockets, there's some fairly large chips and paint is starting to peel off, looks to me just from contact with the limbs. Is it worth attempting to touch up the paint? Or maybe repaint the limb pockets with something like Hammerite? Any other suggestions?

    Or would you just leave it? I know it's an area you can't see in use, but I'm concerned that peeling tends to spread and would prefer for that not to happen, and it's just a bit of a shame in an otherwise immaculate looking riser.

    Thanks





  2. Advertisements like those above are essential to keep AIUK running. If you'd like to remove the Google and Ebay adverts and help us meet our running costs, please consider subscribing for only 1.50 per month. Thank you!
     

  3. #2
    It's an X I've taken part in an AIUK Ironman Shoot.The Fonz Award.AIUK subscriber. Timid Toad's Avatar
    Join Date
    Mar 2006
    Posts
    2,761
    Thanks
    20
    Thanked 235 Times in 209 Posts
    If it's down to the metal, I'd want to protect it, but not to the detriment of the limbs of course.
    "Time is an illusion. Lunchtime doubly so." Douglas Adams

  4. #3
    In the Blue jonUK76's Avatar
    Join Date
    Sep 2016
    Location
    South Wales
    Posts
    111
    Thanks
    28
    Thanked 28 Times in 21 Posts
    Thanks. Yes I think some bare metal is showing. Both ends are similar:



    I was thinking maybe remove the dovetail/alignment mechanism (assuming that's an easy task), wire brush/sand off the old paint, coat of aluminium primer, and a few coats of Hammerite, just on the affected surface? Sound reasonable?

  5. #4
    It's an X I've taken part in an AIUK Ironman Shoot.The Fonz Award.AIUK subscriber. Timid Toad's Avatar
    Join Date
    Mar 2006
    Posts
    2,761
    Thanks
    20
    Thanked 235 Times in 209 Posts
    Not as simple as that, unfortunately. The reason the paint is lifting there is because that is where the limbs sit. It's a vital part of the alignment of your bow.
    If you aren't *extremely* careful you can affect how your limbs sit, which in turn can affect alignment. The riser has left/right adjustment, but if the paint is a few hundredths of a millimetre too thick one side over the other, the limbs will be rotationally out too. Of course, the paint might already be causing this, so you could look at it as an opportunity to adjust your riser's straightness for the good. You might get lucky, but you do need to be aware of the issues involved.
    "Time is an illusion. Lunchtime doubly so." Douglas Adams

  6. #5
    In the Blue jonUK76's Avatar
    Join Date
    Sep 2016
    Location
    South Wales
    Posts
    111
    Thanks
    28
    Thanked 28 Times in 21 Posts
    I see, I hadn't really thought about that Well, I can't say I'm particularly talented with a paint can, but perhaps with several extremely thin coats of spray paint, with very fine sanding between coats, I think it should be possible to get a reasonably smooth and even finish. With the limbs I've tried on it myself (W&W Winex and some budget Samicks), there actually appears to be a small gap between the pocket and the limb under tension, i.e. it looks like it's pivoting on the metal pin rather than the edge of the pocket. As I bought it used, I'm not sure what limbs were used on it previously. Could it depend on the limb design and perhaps position of the limb bolts too?

  7. #6
    It's an X I've taken part in an AIUK Ironman Shoot.The Fonz Award.AIUK subscriber. Timid Toad's Avatar
    Join Date
    Mar 2006
    Posts
    2,761
    Thanks
    20
    Thanked 235 Times in 209 Posts
    Yes, limbs can be designed to sit on slightly different places. But most limbs should be in contact, when strung, with that part of the riser in some way or another. Just slotted together maybe not. However, if you go at it with care, and wait for each coat to dry properly, then fit and string up the limbs and watch for something going wrong, I'd guess you should be able to control what's going on. I would get a load of masking tape on the limbs and carefully measure your string position and mark it off. Then you'll be able to see when paint isn't being applied consistently.
    Now when you observe the string moving out of alignment, you've got to work out which limb, then which side is at fault. I haven't got my head round that yet.
    "Time is an illusion. Lunchtime doubly so." Douglas Adams

Page 1 of 2 12 LastLast

Similar Threads

  1. Suggestions for riser paint
    By Dhansak in forum General Archery Discussion & News
    Replies: 12
    Last Post: 04-06-15, 10:04 AM
  2. Replies: 77
    Last Post: 31-08-10, 04:14 PM
  3. Win&Win Pro Accent Limb Pockets
    By DHBowman in forum Recurve Bow
    Replies: 4
    Last Post: 25-11-08, 06:54 PM
  4. Limbs in limb pockets
    By Neilsence in forum Recurve Bow
    Replies: 6
    Last Post: 19-10-08, 10:41 PM
  5. worn limb pockets ?
    By pHz in forum Recurve Bow
    Replies: 30
    Last Post: 22-01-08, 07:40 PM

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •